What it does: One computer has two network cards. One card is used to connect to the internet, the other one is connected to a switch making up a local network. Two more computers are connected to the switch. They all share the internet connection of the first computer. All computers on the local network can ssh into each other.
I have to register the MAC address of each computer which I want to connect to the network at work. The reason probably has more to do with cost than security.
I do not use /etc/network/interfaces in this example
Instead we're only using Network Manager, but from the CLI.
The sharing is enabled using Firestarter. You can probably figure out how to use it yourself without reading this rather lengthy post, but I'll leave it all up here in case you want to know the exact configuration.
Since I use apt-cache to cut down on network traffic (http://verahill.blogspot.com/2012/01/debian-testing-64-wheezy-apt-cache.html) I don't feel too bad about surreptitiously putting a few additional units online.
This is my network:
internet ----- eth0 -Beryllium - eth2 --- switch----( eth0-tantalum, eth0-boron)
Or in words -- I have three computers. One, Beryllium, has two network cards, eth0 and eth1. eth0 is connected to the internet (dhcp). eth1 is connected to a gigabit switch (essentially a dumb router -- no dhcp). Two more computers are connect to the same switch -- Tantalum (eth0) and Boron (eth0). Tantalum has local ip address 192.168.1.102 and Boron has ip address 192.168.1.101.
I do have an additional ethernet card on Beryllium, eth1, which we will ignore.
This way of sharing an internet connection relies on firestarter, which has one problem -- it won't (easily) allow two network cards on the same local network i.e. if eth0 is connected to the internet and you want both eth1 and eth2 on the same local network, firestarter won't help you.
I also need to be able to ssh from any computer on the local network to any other computer on the local network. This method allows for that. Same goes for apt-cache and mpich.
To satisfy my paranoia I've replaced a lot of the more incriminating numbers with X's.
Firestarter:
Firestarter is a firewall -- you'd typically use it to restrict traffic, not enable it. But iptables -- the true firewall and traffic shaper of linux -- is a powerful and slightly odd beast, and firestarter provides a gui-friendly way of editing some aspects of it.
Install firestarter on your internet connected computer (here, beryllium):
sudo apt-get install firestarter
Start it:
sudo firestarter
Chances are it will ask you questions about internet connected network device -- which is eth0 -- and local network connected device -- here it's eth2. Also, check Enable internet connection sharing. If it doesn't ask you, go to Edit, Preferences and select Firewall -- Network Settings.
In my case I've set it up for static ip. I would suspect it to be fairly easy to set up dhcp as well.
I don't know how to put TWO network cards from the same computer on the same local network.
In the main firestarter windows, under policy, you might want to add the IP addresses of the computers on the local network under 'Allow connections from host' -- but that depends on your needs. I prefer to expose all ports in order to deal with mpich.
You may also want to edit what services are allowed. Firestarter is fairly simple to use.
Configuration: Beryllium
eth0 is connected to the internet, and is assigned an IP address by the university using dhcp.
eth2 is connect to the switch and I've manually set the IP address to 192.168.1.1 in network manager. You can edit the file (see below) directly.
The gateway for eth2 is set to 192.168.1.1. Subnet mask is 255.255.255.0 which shows up as 24 in the configuration file below (i.e. 192.168.1.1;24;192.168.1.2 would mean IP 192.168.1.1, subnet 255.255.255.0 and gateway 192.168.1.2)
sudo cat /etc/NetworkManager/system-connections/eth0
Configuration: Tantalum
sudo cat /etc/NetworkManager/system-connections/eth0
Configuration: Boron
sudo cat /etc/NetworkManager/system-connections/eth0
Quick word on apt-cache:
If you follow this guide: http://verahill.blogspot.com/2012/01/debian-testing-64-wheezy-apt-cache.html
and you're running your apt-cache server on 192.168.1.1 in the example above, change your /etc/apt/sources.list so that
I have to register the MAC address of each computer which I want to connect to the network at work. The reason probably has more to do with cost than security.
I do not use /etc/network/interfaces in this example
Instead we're only using Network Manager, but from the CLI.
The sharing is enabled using Firestarter. You can probably figure out how to use it yourself without reading this rather lengthy post, but I'll leave it all up here in case you want to know the exact configuration.
Since I use apt-cache to cut down on network traffic (http://verahill.blogspot.com/2012/01/debian-testing-64-wheezy-apt-cache.html) I don't feel too bad about surreptitiously putting a few additional units online.
This is my network:
internet ----- eth0 -Beryllium - eth2 --- switch----( eth0-tantalum, eth0-boron)
Or in words -- I have three computers. One, Beryllium, has two network cards, eth0 and eth1. eth0 is connected to the internet (dhcp). eth1 is connected to a gigabit switch (essentially a dumb router -- no dhcp). Two more computers are connect to the same switch -- Tantalum (eth0) and Boron (eth0). Tantalum has local ip address 192.168.1.102 and Boron has ip address 192.168.1.101.
I do have an additional ethernet card on Beryllium, eth1, which we will ignore.
This way of sharing an internet connection relies on firestarter, which has one problem -- it won't (easily) allow two network cards on the same local network i.e. if eth0 is connected to the internet and you want both eth1 and eth2 on the same local network, firestarter won't help you.
I also need to be able to ssh from any computer on the local network to any other computer on the local network. This method allows for that. Same goes for apt-cache and mpich.
To satisfy my paranoia I've replaced a lot of the more incriminating numbers with X's.
Firestarter:
Firestarter is a firewall -- you'd typically use it to restrict traffic, not enable it. But iptables -- the true firewall and traffic shaper of linux -- is a powerful and slightly odd beast, and firestarter provides a gui-friendly way of editing some aspects of it.
Install firestarter on your internet connected computer (here, beryllium):
sudo apt-get install firestarter
Start it:
sudo firestarter
Chances are it will ask you questions about internet connected network device -- which is eth0 -- and local network connected device -- here it's eth2. Also, check Enable internet connection sharing. If it doesn't ask you, go to Edit, Preferences and select Firewall -- Network Settings.
In my case I've set it up for static ip. I would suspect it to be fairly easy to set up dhcp as well.
I don't know how to put TWO network cards from the same computer on the same local network.
In the main firestarter windows, under policy, you might want to add the IP addresses of the computers on the local network under 'Allow connections from host' -- but that depends on your needs. I prefer to expose all ports in order to deal with mpich.
You may also want to edit what services are allowed. Firestarter is fairly simple to use.
Configuration: Beryllium
eth0 is connected to the internet, and is assigned an IP address by the university using dhcp.
eth2 is connect to the switch and I've manually set the IP address to 192.168.1.1 in network manager. You can edit the file (see below) directly.
The gateway for eth2 is set to 192.168.1.1. Subnet mask is 255.255.255.0 which shows up as 24 in the configuration file below (i.e. 192.168.1.1;24;192.168.1.2 would mean IP 192.168.1.1, subnet 255.255.255.0 and gateway 192.168.1.2)
sudo cat /etc/NetworkManager/system-connections/eth0
[802-3-ethernet]
duplex=full
mac-address=XX:XX:XX:XX:XX:XX
[connection]
id=eth0
uuid=XXXXXXXX-XXXX-XXXX-XXXX-XXXXXXXXXXXX
type=802-3-ethernet
timestamp=1326324509
[ipv6]
method=auto
[ipv4]
method=auto
sudo cat /etc/NetworkManager/system-connections/eth2
[802-3-ethernet]
duplex=full
mac-address=XX:XX:XX:XX:XX:XX
[connection]
id=eth2
uuid=XXXXXXXX-XXXX-XXXX-XXXX-XXXXXXXXXXXX
type=802-3-ethernet
timestamp=1326690564
[ipv6]
method=auto
[ipv4]
method=manual
addresses1=192.168.1.1;24;192.168.1.1;
sudo cat /etc/NetworkManager/system-connections/eth0
[802-3-ethernet]
duplex=full
mac-address=XX:XX:XX:XX:XX:XX
[connection]
id=lan
uuid=XXXXXXXX-XXXX-XXXX-XXXX-XXXXXXXXXXXX
type=802-3-ethernet
timestamp=1326152420
[ipv6]
method=auto
[ipv4]
method=manual
dns=XXX.XXX.1.99;
addresses1=192.168.1.102;24;192.168.1.1;
Configuration: Boron
sudo cat /etc/NetworkManager/system-connections/eth0
[802-3-ethernet]
duplex=full
mac-address=XX:XX:XX:XX:XX:XX
[connection]
id=lan
uuid=XXXXXXXX-XXXX-XXXX-XXXX-XXXXXXXXXXXX
type=802-3-ethernet
timestamp=1326152420
[ipv6]
method=auto
[ipv4]
method=manual
dns=XXX.XXX.1.99;
addresses1=192.168.1.101;24;192.168.1.1;
Quick word on apt-cache:
If you follow this guide: http://verahill.blogspot.com/2012/01/debian-testing-64-wheezy-apt-cache.html
and you're running your apt-cache server on 192.168.1.1 in the example above, change your /etc/apt/sources.list so that
deb http://192.168.1.2:3142/ftp.au.debian.org/debian/ testing main contrib non-freebecomes
deb http://192.168.1.2:3142/ftp.au.debian.org/debian/ testing main contrib non-free
This is dummy text. It is not meant to be read. Accordingly, it is difficult to figure out when to end it. But then, this is dummy text. It is not meant to be read. Period.
ConversionConversion EmoticonEmoticon